IL PREZZO INDICATO E' ESCLUSO DAL COSTO DI SPEDIZIONE PER L'IMPORTAZIONE IN ITALIA CHE VERRA' COMUNICATO AL MOMENTO DELL'ORDINE.

Prezzi a partire da euro 3.538. Richiedici un preventivo in base alla colorazione e agli accessori che preferisci!

Un sogno diventa realtà!

I modelli CARF Pitts S12: il primo kit completamente composito di un biplano. Per realizzare questo progetto è stato necessario fare un lavoro ingegneristico serio. Il risultato è sorprendente. Con l'acquisto dei Pitts dei CARF-Models ottieni lo stesso grado di prefabbricazione che già conosci da tutti i nostri altri kit. Non c'è lotta con i dettagli. Tutto il duro lavoro è già fatto. Tutti gli allineamenti vengono controllati. Metti il ​​motore e l'RC sull'aereo e vola!
 
Lo sentiamo ripetutamente: "Un biplano completamente composito può essere solo pesante!". Ebbene, ogni volta che stiamo pilotando il prototipo ancora esistente nello schema rosso “Oracle”, sorridiamo un po 'a tale ipotesi. Anche con un DA-150 molto usato su pipe le prestazioni sono sorprendenti! E sicuramente non ci saranno problemi con il CG, se segui solo alcuni suggerimenti, tutti menzionati nel manuale di istruzioni all'avanguardia.
 
Ma un vecchio 150 bicilindrico non è l'unica scelta di motori. Mentre le caratteristiche di volo dei Pitts possono persino competere con i monoplani collaudati in gara, il suo lavoro preferito è sicuramente un grande spettacolo aereo. Vuoi rendere questo impressionante aereo ancora più impressionante? Mettici dentro un 4 cilindri e nascondilo dietro il fumo sul ponte. Vuoi essere più in scala? Nessun problema. Il popolare Moki 250 radiale a quattro tempi si adatta perfettamente sotto la cappottatura e fornisce potenza sufficiente per tutti i tipi di acrobazie in scala.

General Information

A dream comes true!

The CARF-Models Pitts S12 – the first full composite kit of a biplane. A lot of serious engineering work had to be done to realize this project. The result is amazing. With purchasing the CARF-Models’ Pitts you’re getting the same grade of prefabrication you already know from all our other kits. There is no fighting with details. All the hard work is already done. All alignments are checked. Just put your engine and RC in the plane and go fly!
 
We hear that again and again: “A full composite biplane can only be heavy!”. Well, every time when we are flying the still existing prototype in the red “Oracle”-scheme we do smile a bit about such assumption. Even with a very used DA-150 on pipes the performance is amazing! And there will definitely be no problem with the CG, if you just follow a few tips, all mentioned in the state-of-the-art instruction manual.
 
But an old 150 twin is not the only engine choice. While the Pitts’ flying characteristics can even compete with contest proven monoplanes, its favourite job is a big airshow for sure. You want to make this impressive plane even more impressive? Put a 4-cylinder in it and hide it behind smoke down on the deck. You want to be more scale? No problem. The popular Moki 250 radial four-stroke fits perfectly under the cowling and delivers enough power for all kinds of scale aerobatics.

Features

Let’s give you a taste of all that amazing details, realized in this giant project:

• The full-composite wings consist of five parts in total. The bottom wing is divided in two parts and connected directly to the fuselage - same game as with the monoplanes. The upper wing has a small center part, which is connected with the fuselage through stainless steel cabane struts. In most cases, it can stay connected with the fuselage during transportation. You simply connect the other wing parts to this center part.
• The cabane struts itself are a piece of art. Made from stainless steel and all the welting already done, they come prealigned in the factory. As we promised: All the difficult details are already done for you.
• Cutting is easy! That’s why the engine dome is long enough for every 150-170cc two cylinder engine on the market. But also every four cylinder with about 200cc fits completely under the cowling: Just cut the dome!
• If you use a light 150cc two cylinder engine, it can be necessary to move the elevator servos to the front. Its not that hard as everybody thinks first. We did it on our prototype and for you it’s easy to do it, too – everything is shown in the manual.
• Of course, the Pitts is using flying wires. It wouldn’t be a problem to make the plane strong enough to get rid of them. That would be something, but definitely no Pitts. All the hardware you need is included. The clevises are connected with 3mm bolts and it’s definitely not a hard job to build it up at the field.

Wings

Let's take a closer look at the wings first. Have your ever heard of the "TAVS"-technology, developed by CARF-Models? Well, it stands for "Total Area Vacuum Sandwich" - making the wings so strong and stiff, no wooden or foam-sandwich plane can compete with. A rib and spare structure inside the wing is already prepared for the aluminum spar tube and all the servos. Its made from high quality balsa and plywood, and - where necessary - it is coated with fiberglass or carbon.

It was a real challenge to build the wings light while keeping them strong enough. Like on our monoplanes, everything is prepared, all the alignment work is done. We already took care about all details, which are difficult to realize. And actually, there is a lot more to do than on a monoplane. The centerpart of the upper wing is connected with the caban struts and can stay at its place during transportation for most purposes. The rest is connected with 30mm aluminum alloy tubes and secured with bolts and anti-rotation-pins. The outer struts are full composite parts, strengthend with aluminum inserts which also work as the connectors for the flying wires. They easily fit into pockets already prepared in the wings.

All ailerons are connected with elastic hinges. You should use 2 high power digital servos for each aileron, at least JR 8411 or stronger. The servos are easy to install with the CNC milled frames. As always, there are mounts for JR or Futaba servos included.

Stab

If you are using a light two cylinder engine from 150-170cc, you better should move the 4 elevator servos to the front. We used carbon tubes as pushrods and all the details are shown in the manual. If your choice is a much heavier 4 cylinder or radial engine, the servos can be installed in the tail.

Engine

The cowling is large enough for every two or four cylinder engine in the range from 150 to 220 cc. Also a radial engine like the Moki 250cc is a great choice. The dome is long enough for a 150 and has to be cut if you decide for a four cylinder.

Flying Characteristics

Compared to other popular biplane designs, the Pitts S12 features a long tail and a big wingspan. This is why the Pitts "behaves" really good, even for a biplane! It flies straight, it snaps like it should and it can beat any wind. It definitly doesn't fly like a blimp.

Like every other biplane, the Pitts S12 is great for all the crazy knife-edge stuff. The large fuselage side area provides the lift, while the two wings make it stable. It never get's boring to play with that!

The Pitts S12, especially in the clipped wing "Python" version shown here, is able to do possibly the fastest torque rolls ever seen. The ailerons are still highly effective in high-alpha maneuvers and so you have the choice, if you use them with or against the torque. From slow to fast, the Pitts can do everything!

Conclusion

Besides that, the Pitts can do all the stuff, what made biplanes so popular. Crazy spins, great and amazingly slow knife-edges and harriers stable as driving a truck. All that combined with the impressive appearance of this Giant in the air let you be the star of every show.

The CARF Models Pitts S12 – the biplane done right, finally!